ArmbianHelper changed the topic of #armbian to: armbian - Linux for ARM development boards | www.armbian.com | Github: github.com/armbian | Commits: #armbian-commits | Developer talk: #armbian-devel | Forum feed: #armbian-rss | Off-Topic: #armbian-offtopic | Logs: -> irc.armbian.com
zeemate has quit [Ping timeout: 248 seconds]
Suspect has joined #armbian
darkgeek1 has quit [Read error: Connection reset by peer]
darkgeek1 has joined #armbian
darkgeekyang has joined #armbian
darkgeek1 has quit [Ping timeout: 252 seconds]
Suspect has quit [Remote host closed the connection]
Suspect has joined #armbian
Suspect has quit [Read error: Connection reset by peer]
darkgeekyang has quit [Read error: Connection reset by peer]
Suspect has joined #armbian
darkgeekyang has joined #armbian
norwich_ has joined #armbian
norwich has quit [Ping timeout: 248 seconds]
norwich_ is now known as norwich
Suspect has quit [Read error: Connection reset by peer]
archetech has quit [Quit: Leaving]
darkgeekyang has quit [Read error: Connection reset by peer]
darkgeekyang has joined #armbian
darkgeek1 has joined #armbian
darkgeekyang has quit [Ping timeout: 248 seconds]
jclsn has quit [Ping timeout: 248 seconds]
darkgeek1 has quit [Read error: Connection reset by peer]
<schwar3kat>
I see that I can merge this without review. Is this what is expected in this repo or should review be compulsory?
schwar3kat has quit [Quit: Offline]
Suspect has joined #armbian
nickodd has joined #armbian
Suspect has quit [Read error: Connection reset by peer]
Suspect has joined #armbian
Suspect has quit [Remote host closed the connection]
darkgeekyang has joined #armbian
darkgeek1 has quit [Ping timeout: 248 seconds]
Suspect has joined #armbian
<Armbian-Discord>
<IgorPec> yes, you could just merge that ... difficult to "review" binary blobs 😉
Suspect has quit [Ping timeout: 252 seconds]
arch3r has quit [Read error: Connection reset by peer]
arch3r has joined #armbian
schwar3kat has joined #armbian
Suspect has joined #armbian
<schwar3kat>
Does anyone have a standard way to configure sys-triggered board LEDs for individual boards in Armbian Build? Just checking first... otherwise I want to start a conversation on the forum and throw around some ideas.
<schwar3kat>
I am aware of the stuff configured in armbian services.
nickodd has left #armbian [#armbian]
zeemate has joined #armbian
Suspect has quit [Read error: Connection reset by peer]
zeemate has quit [Ping timeout: 248 seconds]
arch3r has quit [Read error: Connection reset by peer]
arch3r has joined #armbian
pablocastellanos has quit [Ping timeout: 260 seconds]
<Armbian-Discord>
<Werner> Since there aren't any standards various (or most) vendors are following it is kind a hard to make a standard way to configure those 😄
<Armbian-Discord>
<edwardoid> Guys, I enabled UART 3, but RX works, and TX does not. So I have 2 questions:
<Armbian-Discord>
<edwardoid> 1. If in one direction connection works, then I believe my issue is HW related, something is broken in pin->chip connection. Am I right?
<Armbian-Discord>
<edwardoid> 2. UART2 on my board has GPIO feature too. If I enable UART2, and use GPIO pins(not the ones connected to UART) will it work?
<Armbian-Discord>
<meteyou> sry for the delay. i don't know if a partnership is suitable for me. i'm just a small open source maintainer with no sales model of my software. i'm just in the process of providing more SBCs with pre-built images including pre-installed software.
Suspect has quit [Quit: Leaving]
Laskolnyk has joined #armbian
haritz has quit [Ping timeout: 248 seconds]
joshaspinall has joined #armbian
Proxysna has quit [Remote host closed the connection]