buzzmarshall has quit [Quit: Konversation terminated!]
Guest98 has joined #beagle
Guest98 has quit [Quit: Ping timeout (120 seconds)]
otisolsen70 has joined #beagle
nparafe has quit [Ping timeout: 256 seconds]
nparafe has joined #beagle
Shadyman has quit [Quit: Leaving.]
Guest56 has joined #beagle
florian has joined #beagle
Guest56 has quit [Ping timeout: 256 seconds]
starblue1 has quit [Ping timeout: 240 seconds]
starblue1 has joined #beagle
lucascastro has quit [Remote host closed the connection]
lucascastro has joined #beagle
CrazyEddy has quit [Ping timeout: 240 seconds]
buckket has quit [Quit: buckket]
buckket has joined #beagle
rob_w has joined #beagle
buzzmarshall has joined #beagle
Guest9 has joined #beagle
<Guest9>
i have an issue. i have designed a cape for the bbb but im finding as soon as i plug the bbb in to the cape. it gets fried ie the power light flashes quickily once.
<Guest9>
the bbb is powered via the 5v vdd pin and gnd pins.
<Guest9>
about 32 gpio pins are then connected to a level shifter and have noticed the level shifters are putting a voltage of 3.3V back to the gpio pins. not sure if this could be the issue or not
Guest991 has joined #beagle
Guest9 has quit [Ping timeout: 256 seconds]
Guest991 has quit [Quit: Client closed]
rob_w has quit [Quit: Leaving]
<vd_>
zmatt: so it is safe to assume that the beaglebone blue/green/enhanced are derived from the black, right?
florian has quit [Quit: Ex-Chat]
ikarso has joined #beagle
zjason` is now known as zjason
otisolsen70 has quit [Quit: Leaving]
Guest38 has joined #beagle
m-atoms has joined #beagle
Guest38 has quit [Client Quit]
dkaiser has joined #beagle
<zmatt>
they are yes
<dkaiser>
I am planning to do so debugging of the Debian (Bullseye) installer on beaglebone black. Any recommendations? Setting up a debian installer cross build environment?
<rcn-ee>
dkaiser, disable 'quiet' boot the current version, and report what fails...
<rcn-ee>
i think there are a few kernel bugs, that haven't been merged into debian's kernel..
<rcn-ee>
dkaiser, pretty sure the current bbb bug is: enable: CONFIG_TI_CPSW_SWITCHDEV
vagrantc has joined #beagle
<dkaiser>
rcn-ee, the installed bullseye system works on the BBB, except that I must manually configure the ethernet system as the debian installer failed to detect it.
<dkaiser>
my goal is to identify what is causing the failure to detect the ethernet driver during the debian installer.
<dkaiser>
rcn-eee, what methods can you suggest for "disable 'quiet' boot of the current version...?
<rcn-ee>
pretty sure the last issue, was that CONFIG_TI_CPSW_SWITCHDEV was not set ot built-in or module.. thus ethenet never comes up..
nparafe has quit [Ping timeout: 256 seconds]
nparafe has joined #beagle
dwkai_ has joined #beagle
dkaiser has quit [Ping timeout: 256 seconds]
dwkai_ has quit [Quit: Leaving]
dwkai_ has joined #beagle
dwkai_ has left #beagle [#beagle]
dwkai_ has joined #beagle
dwkai_ has quit [Client Quit]
dkaiser has joined #beagle
set_ has quit [Ping timeout: 240 seconds]
Shadyman has joined #beagle
samnob has quit [Quit: I'm not smart enuf to edit bouncer.conf]
samnob has joined #beagle
samnob_ has joined #beagle
samnob has quit [Ping timeout: 240 seconds]
ikarso has quit [Quit: Connection closed for inactivity]
Stanto has quit [Read error: Connection reset by peer]
<zmatt>
dkaiser: what do you mean with "methods" for disabling quiet boot? just remove the 'quiet' option from the kernel commandline parameters
<dkaiser>
zmatt, thank you
rcn-ee has quit [Remote host closed the connection]