<static_rocket>
questions about wireless ap. been down that road on other products. it's frustrating how hard it is to find a good wireless interface that actually properly supports ap. haven't even attempted with the beagle devices yet. intel still can't even figure out how to do it reasonably and they wrote their own wireless daemon as a replacement for networkmanager.
<static_rocket>
it's reasonable they are frustrated. people tend to overlook that feature
<static_rocket>
well, it was supposed to be a replacement for wpa_supplicant but then it snowballed and started including advanced interface management and bluetooth control so now it basically is a replacement for networkmanager
set_ has quit [Read error: Connection reset by peer]
set_ has joined #beagle
<zmatt>
static_rocket: it doesn't replace wpa_supplicant
<zmatt>
unless you're confusing connman and iwd
<zmatt>
oh wait you're talking about iwd not connman... are you saying it's also a network manager? I wasn't aware of that
<zmatt>
oh yeah it does actually support (optional and very rudimentary) network management...
<zmatt>
not sure when you'd use that... I guess it could be handy if you're using iwd with systemd-networkd and for some weird reason you have a requirement to use custom network settings for some wifi networks
brook has joined #beagle
<static_rocket>
feature creep made the two hauntingly similar. connman is still their preferred connection manager though
<zmatt>
at a quick glance I didn't see anything about iwd supporting any sort of management of non-wifi interfaces
<zmatt>
nor would I expect it to
buzzm has quit [Quit: Konversation terminated!]
brook has quit [Ping timeout: 248 seconds]
<static_rocket>
huh. they may have actually dropped the bluetooth support in iwctl. good on em
brook has joined #beagle
<static_rocket>
i only briefly played with it in college. unfortunately it only supported EAP-PEAP as well as nm did at the time so it didn't last long.
zmatt has quit [Ping timeout: 268 seconds]
aussetg has quit [Remote host closed the connection]
aussetg has joined #beagle
vagrantc has quit [Quit: leaving]
ikarso has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
Shadyman has quit [Quit: Leaving.]
rob_w has joined #beagle
otisolsen70 has joined #beagle
starblue has quit [Ping timeout: 248 seconds]
zmatt has joined #beagle
starblue has joined #beagle
Stat_headcrabed has joined #beagle
SteveMarple has joined #beagle
florian has joined #beagle
ikarso has quit [Quit: Connection closed for inactivity]
ft has quit [Quit: leaving]
tomba has quit [Ping timeout: 265 seconds]
tomba has joined #beagle
CrazyEddy has quit [Ping timeout: 250 seconds]
yCrazyEdd has joined #beagle
starblue has quit [Ping timeout: 256 seconds]
starblue has joined #beagle
_av500_ has quit [Remote host closed the connection]
av500 has joined #beagle
Parduz has joined #beagle
<Parduz>
how can i show the penguin logo at boot, instead of the blinking cursor only?
<Parduz>
@zmatt: should i open an issue about the RTC overlay which is'nt rtc0 but rtc1? i don't know WHERE should i open the issue...
rob_w has quit [Remote host closed the connection]
brook has quit [Ping timeout: 240 seconds]
brook has joined #beagle
brook has quit [Quit: Leaving...]
florian has quit [Quit: Ex-Chat]
otisolsen70 has quit [Quit: Leaving]
Parduz has quit [Read error: Connection reset by peer]
Guest6222 has joined #beagle
<Guest6222>
Hi
Guest6222 has quit [Client Quit]
Guest626 has joined #beagle
<Guest626>
Hi Dr
Guest626 has quit [Client Quit]
buzzmarshall has joined #beagle
vagrantc has joined #beagle
wiagn has joined #beagle
Stat_headcrabed has quit [Ping timeout: 240 seconds]
wiagn is now known as Stat_headcrabed
Stat_headcrabed has quit [Quit: Stat_headcrabed]
otisolsen70 has joined #beagle
Stat_headcrabed has joined #beagle
Stat_headcrabed has quit [Client Quit]
behanw has quit [Quit: Connection closed for inactivity]
ft has joined #beagle
riri has joined #beagle
riri has quit [Client Quit]
<set_>
Parduz: There are some overlay issues that can be raised on git.beagleboard.org .
<set_>
You would just need to find the correct repo.
otisolsen70 has quit [Quit: Leaving]
<set_>
The repo. is usually Beagleboard-DeviceTrees.
<set_>
Or... BeagleBone-DeviceTrees. I forget which one. Let me check.