13:23 <LEBot> [slack] <jernej> montjoie: Is it the same version as in LE? If so, you probably don't use Crust, right?

15:28 <montjoie> jernej: I tried a vanilla uboot v2022.07

15:28 <LEBot> [slack] <jernej> montjoie: can you try it with crust too?

15:29 <LEBot> [slack] <jernej> I suspect that what breaks it

15:38 <montjoie> jernej, my current try is https://paste.debian.net/1253616/

15:39 <montjoie> but I dont checked if crust config exists

15:39 <montjoie> that could explain the breakage

16:03 <LEBot> [slack] <jernej> montjoie: it doesn't: https://github.com/crust-firmware/crust/tree/master/configs

16:05 <LEBot> [slack] <jernej> use config from similar board, afaik most are similar, at least in the part that Crust is interested in

16:05 <LEBot> [slack] <jernej> if it works, open PR with config for your board

16:44 <fuxxy> Running LE 10.0.2 on a Rpi4. Noticing that NTP is spotty, it won't come up at boot time, but if I go in settings and verify NTP, the time is changed when I press OK. Next reboot the time is off again. (I run NTP on an ActiveDirectory Domain server, that's always available.)

16:46 <montjoie> jernej i tried with nanopi_m1_defconfig but no change

16:46 <fuxxy> Also, 'systemctl status' shows system is degraded (network-online.service failed), but there's nothing in dmesg or journalctl saying why

16:48 <LEBot> [slack] <jernej> montjoie: are you sure that nanopi_m1_defconfig is compatible? please check schematic

16:50 <montjoie> jernej not sure at all, I will check

16:51 <LEBot> [slack] <jernej> other than telling you what to check, I can't help you much. I don't have that board.

16:52 <montjoie> jernej: no problem, at least I know a workaround, but it will be easier if I found the problem for upstreaming my change

16:52 <LEBot> [slack] <jernej> you can also try to remove all H3 U-Boot related patches, which will also result in disabling Crust and see if it is works

16:56 <montjoie> jernej: I changed crust_config but make didnt rebuilt crust...

17:02 <LEBot> [slack] <jernej> oh right, you have to clean u-boot and build again

17:02 <montjoie> jernej: in fact I cleaned uboot/crust directory, but crust was not rebuilt at all

17:03 <montjoie> I try a full clean build

18:17 <mack> fuxxy_laptop: have you tried the "wait for network on start" or whatever it's called in LE settings?

18:23 <fuxxy_laptop> Yes that's enabled.

18:25 <fuxxy_laptop> it pauses during boot, but before the Kodi splash screen appears, eventually timing out. Once Kodi loads, everything appears normal - I can connect to plex and my media without issue.

18:26 <fuxxy_laptop> I'm reading that connman attempts to connect to [http://ipv4.connman.net/online/status.html] for it's online test, which I can resolve and connect after the system boots.

18:56 <fuxxy_laptop> Well there's a problem... Regional/Timezone got reset to blank somehow

18:57 <fuxxy_laptop> Guess I need to figure out where that's saved and set it up in Zabbix

19:00 <fuxxy_laptop> I set everything back up, and ensured 'wait for network' was turned on. I also set the timeout to 300. I've been sitting here at the LibreELEC boot logo for 2 mins already waiting for network to come up. I can't ping it from the router, so net's definately not up yet, but once the timer expires, kodi will load and network will be just fine

19:15 <fuxxy_laptop> finally booted, and still no network. It looks like the "Connect automatically" setting got flipped to off. Lets try again.

19:16 <fuxxy_laptop> Alright, connected this time. Didn't even have to wait the full 5 mins. I'll call it user error unless it comes back.

19:58 <appas> how to debug a non-booting libreelec? i have a mecool m8s pro+; the 9.2.5 build from https://github.com/dtechsrv/LibreELEC-AML boots, but there is no support for the wifi chip. the 9.2.6 snapshot from http://libreelec.dtech.hu/snapshots/20220911/ adds this support, but fails to boot on my box.

20:23 <mack> appas: dtech seems to be helping you in the community build thread :)

20:49 <appas> mack: that's true, he's been very kind; i was just wondering if there were any ideas as to what to do while i wait for him to reply at https://github.com/dtechsrv/LibreELEC-AML/pull/14