12:07 <DasPoseidon> Hey, I have an issue with picons not loading with pvr.hts (tvheadend pvr addon) when the password ends with an # (probably also when it just contains one, didn't test) due to it trying to access http://admin:passw/#@SERVER/ instead of http:// admin:passw#@SERVER . Im running the LibreELEC 10 Beta on RPI4, but it also didn't work on LibreELEC 9

12:08 <DasPoseidon> This does work on every other kodi install I have (Android, (Arch)Linux, Windows)

16:03 <Forage> Good afternoon. My Mecool KIII Pro with CoreElec died so I switched back to a RPi (4) with LibreElec again. For a smooth start I'd like to change the resolution of the splash screen to match that of the RPi initial start and the Kodi UI. "disp_cap" doesn't seem to do the trick this time. How can I change it?

16:06 <Forage> Also, I seem to suffer from this issue: https://forum.kodi.tv/showthread.php?tid=144956&pid=2128291#pid2128291, where I need to turn off and on the TV every time I reboot the RPi to make the play/stop buttons on the remote work. Does anyone know of a fix instead of sticking to the work-around?

16:07 <Forage> (playing with LibreELEC (Matrix) 10.0 RC1)

16:08 <chewitt> Forage it's possible to run the GUI at 4K, but in a week or so you'll be back to complain about slow menus and such

16:08 <Forage> don't care about 4K with a 1080p TV ;)

16:08 <chewitt> it's best to run GUI at 1080p and set the whitelist to switch to 4K only when needed for playback

16:09 <chewitt> this is the default behaviour so nothing to change if the TV is 1080p only

16:09 <Forage> I want it at 60hz instead of 50

16:09 <chewitt> change it to 60Hz then

16:10 <Forage> I changed the config.txt and Kodi UI, but the splash remains at 50

16:10 <chewitt> normally that's the default too .. but depends on what EDID the TV gives out

16:10 <Forage> the LE splash I mean

16:11 <chewitt> in LE10 images you shouldn't need to fiddle with config.txt unless enabling overlays

16:11 <Forage> it was needed to get the RPi start at 60

16:12 <Forage> than the splash jumps back to 50, followed by kodi at 60 again

16:12 <chewitt> what did you add to force it?

16:13 <Forage> hdmi_group 1 hdmi_mode 16

16:13 <chewitt> remove that

16:13 <Forage> nothing more, nothing less

16:14 <Forage> if I do I have the RPi initial start and splash at 50

16:14 <chewitt> add video=HDMI-A-1:1920x1080M@60D to cmdline.txt

16:15 <Forage> ah

16:15 <Forage> cheers

16:15 <chewitt> see if that works

16:16 <chewitt> needs to be on the same line as "quiet" not on a separate line

16:17 <chewitt> I don't use CEC so can't help with that issue

16:17 <Forage> i was just about to ask, thanks

16:18 <chewitt> I always found CEC to be a pain in the arse so I disable it in my AVR to avoid problems

16:19 <chewitt> I use a couple of BT remotes and a couple of flirc USB devices

16:19 <Forage> splash is at 60 now, initial RPi boot back to 50, trying it together with the lines in config.txt

16:22 <Forage> works like a charm, cheers

16:24 <chewitt> np

16:24 <Forage> CEC was working fine with the mecool, now with the RPi I have the play/stop buttons only working if the tv is (re)started after a RPi reboot and button presses sometimes being applied twice

16:25 <Forage> I played a lot with the cec settings in kodi in the past for the latter when I used a RPi 2. I'll see if I can dig the setting up again

17:19 <ponyofdeath> hi, upgrading my pi4 to 10 rc1 and seems like its locking up with my 4k tv

17:19 <ponyofdeath> anyone else seeing this?

17:19 <ponyofdeath> i upgraded from previous betas which were fresh install

17:19 <ponyofdeath> now even did another frech rc1 install and after it boots to kodi hdmi input dissapears