<mattb0ne>
zmatt I thought it was bad to power both pins on P9
<mattb0ne>
there are four headers on that cable I would assume you only should have two one for 5v_vdd and gnd
brook_ has quit [Remote host closed the connection]
brook has joined #beagle
<zmatt>
mattb0ne: "bad to power both pins on P9" ??
<zmatt>
P9.01 and P9.02 are both ground, P9.05 and P9.06 are both VDD_5V
<zmatt>
while in practice you can get away with connecting only one GND pin and one VDD_5V pin it is preferred to connect both ground pins and both VDD_5V pins to distribute the supply current across two pins, since the beaglebone can draw up to 2A and the header pins are iirc officially only rated for 1A per pin
brook has quit [Remote host closed the connection]
<mattb0ne>
ok
vagrantc has quit [Quit: leaving]
mattb0ne has quit [Ping timeout: 260 seconds]
mattb0ne has joined #beagle
xet7 has quit [Remote host closed the connection]
v0n has quit [Quit: WeeChat 3.7.1]
vvn has joined #beagle
brook has joined #beagle
mattb0ne has quit [Remote host closed the connection]
mattb0ne has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
<set_>
10:00
<set_>
did you think I would quit?
mattb0ne has quit [Ping timeout: 260 seconds]
AKN has joined #beagle
ikarso has joined #beagle
brook has quit [Remote host closed the connection]
buzzmarshall has quit [Quit: Konversation terminated!]
vagrantc has joined #beagle
vagrantc has quit [Quit: leaving]
ikarso has quit [Quit: Connection closed for inactivity]
Stat_headcrabed has joined #beagle
Stat_headcrabed has quit [Quit: Stat_headcrabed]
Shadyman has quit [Quit: Leaving.]
Stat_headcrabed has joined #beagle
mattb0ne has joined #beagle
yCrazyEdd has joined #beagle
CrazyEddy has quit [Ping timeout: 255 seconds]
mattb0ne has quit [Ping timeout: 260 seconds]
mattb0ne has joined #beagle
mattb0ne has quit [Quit: Leaving]
wiagn has joined #beagle
Stat_headcrabed has quit [Ping timeout: 255 seconds]
wiagn is now known as Stat_headcrabed
Guest40 has joined #beagle
<Guest40>
I'm looking for a Kicad or Eagle footprint of the AI-64. Does anyone have one? Or a copy of Allegro that they could export one from jkridner
<Guest40>
Or is there a way to generate a footprint from a gerber?
Guest40 has quit [Ping timeout: 260 seconds]
zjason` is now known as zjason
AKN has quit [Read error: Connection reset by peer]
xet7 has joined #beagle
rob_w has joined #beagle
brook has joined #beagle
xet7 has quit [Remote host closed the connection]
brook has quit [Remote host closed the connection]
buzzmarshall has joined #beagle
SJFriedl has quit [Quit: Leaving]
brook has joined #beagle
xet7 has joined #beagle
SJFriedl has joined #beagle
Stat_headcrabed has quit [Quit: Stat_headcrabed]
thinkfat has joined #beagle
otisolsen70 has joined #beagle
otisolsen70 has quit [Remote host closed the connection]
thinkfat has quit [Quit: Konversation terminated!]
thinkfat has joined #beagle
thinkfat has quit [Quit: Konversation terminated!]
thinkfat has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
brook has quit [Read error: Connection reset by peer]
brook has joined #beagle
brook has quit [Remote host closed the connection]
brook has joined #beagle
rob_w has quit [Read error: Connection reset by peer]
brook has quit [Remote host closed the connection]
brook has joined #beagle
brook has quit [Remote host closed the connection]