Werner changed the topic of #armbian to: armbian - Linux for ARM development boards | www.armbian.com | Github: github.com/armbian | Announcements: #armbian-announcements | Developer talk: #armbian-devel | Off-Topic: #armbian-offtopic | Logs: -> irc.armbian.com
zeemate has quit [Ping timeout: 248 seconds]
buzzmarshall has quit [Quit: Konversation terminated!]
lemonzest has quit [Quit: WeeChat 4.5.0]
lemonzest has joined #armbian
laz0r has quit [Read error: Connection reset by peer]
laz0r has joined #armbian
Treibholz has quit [Ping timeout: 265 seconds]
Treibholz has joined #armbian
coldfeet has joined #armbian
<DC-IRC> [Discord] <superkali> Happy Christmas everyone 🎄
coldfeet has quit [Quit: Lost terminal]
zeemate has joined #armbian
coldfeet has joined #armbian
alekksander has joined #armbian
coldfeet has quit [Ping timeout: 252 seconds]
jasmint has quit [Ping timeout: 244 seconds]
jasmint has joined #armbian
coldfeet has joined #armbian
[TheBug] has quit [Ping timeout: 252 seconds]
<DC-IRC> [Discord] <quer_beet_ein> I´m stuck on bringing UP CAN when boot.
<DC-IRC> [Discord] <quer_beet_ein> if i type in terminal :
<DC-IRC> [Discord] <quer_beet_ein> sudo ip link set can0 type can bitrate 1000000
<DC-IRC> [Discord] <quer_beet_ein> sudo ip link set can0 up
<DC-IRC> [Discord] <quer_beet_ein> i got my connection to klipper MCU btu after reboot i have to redo this.
<DC-IRC> [Discord] <quer_beet_ein> Make file in /etc/network/interfaces.d/can0 with the following imstructions did nothing
<DC-IRC> [Discord] <quer_beet_ein> allow-hotplug can0
<DC-IRC> [Discord] <quer_beet_ein> iface can0 can static
<DC-IRC> [Discord] <quer_beet_ein> bitrate 1000000
<DC-IRC> [Discord] <quer_beet_ein> up ifconfig $IFACE txqueuelen 1024
<DC-IRC> [Discord] <Werner> Not an expert but tried to adding
<DC-IRC> [Discord] <Werner> auto can0
<DC-IRC> [Discord] <Werner> line?
<DC-IRC> [Discord] <quer_beet_ein> where to add?
<DC-IRC> [Discord] <Werner> In the interface file where the other stuff you mentioned is
<DC-IRC> [Discord] <Werner> "auto: This keyword is used to specify interfaces that should be automatically brought up at boot time. For example: auto eth0"
<DC-IRC> [Discord] <quer_beet_ein> did not change anything.... ip a says after reboot state DOWN
<DC-IRC> [Discord] <quer_beet_ein> i dont know if i am in the right directory...... because i had to make the dir and i don´t know if armbian load this file by bootign
<DC-IRC> [Discord] <quer_beet_ein> i dont know if i am in the right directory...... because i had to make the dir and i don´t know if armbian load this file by booting
<DC-IRC> [Discord] <Werner> Again not an expert but etc network interfaces stuff is related to ifupdown management. Armbian uses netplan for management.
<DC-IRC> [Discord] <Werner> Just a quick search
buzzmarshall has joined #armbian
[TheBug] has joined #armbian
MrFixIt has quit [Remote host closed the connection]
Mangix has quit [Read error: Connection reset by peer]
Mangix has joined #armbian
<DC-IRC> [Discord] <quer_beet_ein> got it to work thank you
coldfeet has quit [Remote host closed the connection]
MrFixIt has joined #armbian
zeemate has quit [Ping timeout: 246 seconds]
wootehfoot has quit [Read error: Connection reset by peer]